Title | Statistics | Last post |
---|---|---|
Canik Fanatik on Social Media
by Canik Fanatik - - in: INFORMATION AND ANNOUNCEMENTS Just a reminder, we have groups on social media. In the event that the forum should ever be offline, you can connect with members on Facebook and...
|
13 Replies 34737 Views |
by ncjw
|
Title | Statistics | Last post |
---|---|---|
Replacing Broken Freedomsmith Trigger Safety
by GlennSFX - I posted this in my SFX Build thread but wanted to add it here in the Troubleshooting Area.
Background... I was shooting my SFX at the outdoor range... |
18 Replies 752 Views |
by LT USN (Ret.)
|
Title | Statistics | Last post |
---|---|---|
Canik TP9SF Not Ejecting Properly
by hutchmm138 - Hello all, new member here.
Today I took my TP9SF out to the range for the first time. Unfortunately, with nearly each round fired, the spent casing... |
1 Replies 20 Views |
by buddyd157
|
TP9 SA slide not locking back after every Mag
by Joeyjoe57 - Bought a used TP9SA and it shoots great. About 50% of the time the slide won’t lock back after the last round. I’m sure this has been discussed...
|
7 Replies 72 Views |
by DallasCajun
|
red dot on METE
by alexis1986 - hello, i bought the TP9SFX METE mostly because it was optic ready and it keep the iron sight in backup, so i get an aftermarket docter sight III for...
|
3 Replies 45 Views |
by Carter3000
|
Canik TP9 ELITE SC PLUNGER AND SPRING
by hrmancha20 - So I took a part my slide. FULL DISASSEMBLY. And the plunger and spring shot out like a .22 cartridge lol. Anyone know where I can order these two...
|
1 Replies 25 Views |
by Carter3000
|
Can't get slide back on Elite SC
by Den46 - Removed slide without first pulling trigger, it moved forward about an inch then tilted up and came off, when I went to put it back on I did it like...
|
13 Replies 107 Views |
by colonel00
|
TP9SA Mod 2 - Threaded Barrel Issue - Is It Actually 1/2x28???
by EverythingOutdoors7 - Gents,
Excited to have found this forum. I recently purchased a linear compensator(aka flash can) that is threaded to fit a 1/2x28 threaded barrel.... |
4 Replies 32 Views |
by EverythingOutdoors7
|
Problem removing plate to install new red dot mount plate
by krcourson - Hi all, I've removed the 2 screws and washers and can't get the plate off of my TP9 Elite Combat to put on the #2 RMR plate. Is there something I'm...
|
2 Replies 51 Views |
by krcourson
|
Slide release spring loose
by Stumasters - Greetings. I’m afraid I’ve turned what should have been an easy DIY into a frustration event when I attempted to upgrade my SA slide release to my...
|
9 Replies 51 Views |
by buddyd157
|
Recoil spring on guide rod not seated correctly? Elite SC
by JTCB - After a day at the range I disassembled my SC to clean it and I noticed the spring on the guide rod didn’t look right. Tried reassembling the firearm...
|
3 Replies 29 Views |
by buddyd157
|
TP9 Elite Combat Executive - striker stuck, can't field strip
by bluke01 - Hi all,
I just got a new TP9 Elite Combat Executive and have put about 100 rounds through it with no problems. Got home and went to field strip but... |
2 Replies 48 Views |
by bluke01
|
Elite SC: Installing Slide Stop Pin
by DallasCajun - I just 'completed' the installation of a new Freedomsmith trigger for my Elite SC, but one of the last steps is driving me bat-$&*^.
Basically, the... |
2 Replies 23 Views |
by colonel00
|
SAI barrel rust
by aspen - Has anyone has issued with the SAI barrel rusting? If that what it is.... image is attached here. Let me know what you think. Gun has never been shot...
|
4 Replies 61 Views |
by buddyd157
|
TP9SFX BROKEN +2 BASE PLATE
by COACH1106 - I just had my baseplate explode off the mag yesterday at the range. Looks like the lip that the mag slides into just snapped off. Mag was only loaded...
|
3 Replies 54 Views |
by COACH1106
|
Swampfox Sentinel screws
by Rvegasfx - Hey Canik Fam,
Has anyone mounted the Sentinel on the SC using the provided swampfox M4 screws and the mounting plate . I have it mounted and it... |
0 Replies 33 Views |
by Rvegasfx
|
Slide not in battery won’t come off
by Xican - New gun TP9SF with close to 500 rounds through it with no issues. Love the gun and it is the perfect complement to my Sig P938. Added laser to the...
|
3 Replies 63 Views |
by Xican
|
TP9SA Mod 2 Light Mount issue
by colonel00 - Apologies in advance, new to the forum and trying to search has only lead to one thread but it was kind of different from my issue.
I have a TP9SA... |
68 Replies 1058 Views |
by apellegrini84
|
Elite combat front slide looseness
by cnkmomer - Hello Dear forum users,
im concerned about a little play in the front of the slide as you can hear there is a small looseness. It could be a... |
9 Replies 144 Views |
by cnkmomer
|
10 Rd Mag Issue for TP9SF
by Reggietsfree - Hey Guys,
Purchased a TP9SF a few day back and ordered 10 rd mag from CANIK. It arrives today and I Ioad it with Federal Hydro-Shok 124 grain...and... |
15 Replies 67 Views |
by Reggietsfree
|
TP9 Elite Combat Executive Last round hold open
by Bagman - During the first range session with my Elite Combat Executive, I fired 150 rounds through the gun with no issue at all. I installed a Vortex Venom...
|
6 Replies 41 Views |
by Bagman
|
Right now the only "Gun" related[…]
Welcome from another SFx enthusiast in the Southea[…]
Picked up 4 boxes of .45 tonight at a local gun r[…]